Uninterrupted Power from the Ground Up:
The Bronco All-In-One
The ultimate “Backup Ready” integrated main electrical panel designed for new home and condo construction.
Future-proof your next residential build with the Bronco All-In-One. Designed to be integrated directly into a new construction rough-in sequence, the all-in-one system combines a standard load center with an essential circuits panel in one sleek, interior-mounted unit.
Pre-Wired for Peace of Mind
The Bronco All-In-One shifts power resilience from an expensive afterthought to an integrated home feature. By installing our integrated load center, during the new construction rough-in, your property is instantly “Bronco Backup Ready”.
No Rewiring Required Later
Once the panel is roughed in, the home is completely ready for backup power to the essentials — no costly or invasive electrical rewiring is needed down the line.
Indoor & Space-Saving
Designed and UL approved for interior wall-mounted installation, making it ideal for condominiums, urban builds, and space-constrained residential homes.
A Clean Aesthetic
No generator, no solar, no fuel lines, or bulky outdoor exterior equipment to disrupt the property’s design.
Keeping the Core Running
Typical pre-wired essential loads include individual items on each circuit, such as:
- Garage Door
- Refrigerator
- Gas Hot Water and Gas Stove ignition
- C-PAP and Medical Equipment
- LED Lighting
- Living Room and WiFi
- Home Office
- Receptacles to Charge Cell Phone and Laptop
Ensure your buyers never lose their most critical connections during a grid failure.
Designed With the Installer in Mind
The Bronco All-In-One is UL9540A approved and provides a familiar installation approach for electrical contractors, turning a high-margin energy resilience solution into a straightforward rough-in.
Technical Documents & Installation Guides
Ready to spec the Bronco All-In-One for your upcoming builds? Our Electrician Quick Reference and Installation Overview details the full new construction rough-in sequence.
Note: The quick reference sheet is a visual sequence overview only. It is not an engineering document or code-compliance reference. Always follow full manufacturer instructions and applicable electrical codes.
BRONCO POWER BOOST ALL-IN-one FAQ
Can the All-In-One be installed in condos, high-rises, or zero-lot-line properties?
Yes. The system is designed specifically for an interior wall-mounted installation. It requires no exterior pad, outdoor enclosure, or external venting. This makes it an ideal fit for condominiums, high-rise units, and urban or space-constrained residential installations.
What does "Bronco Backup Ready" mean for my construction timeline?
It means your electricians integrate the main electrical panel during the standard new construction rough-in sequence. By installing the enclosure, the essential circuits panel, and a 40 Amp feeder breaker, the home is fully prepared for backup power. The battery and Bronco Sled can then be added and commissioned during a separate visit later, meaning no invasive rewiring is needed by the homeowner down the road.
Will installing this system complicate or delay my permitting process?
No, the All-In-One actually offers a simplified permitting process compared to traditional backup generators. Because it is a self-contained indoor unit that operates without generators, solar panels, fuel, gas lines, or exterior equipment, it avoids many of the common zoning and permitting roadblocks associated with outdoor power systems.
What specific essential circuits does the system support during an outage?
The essential circuits panel is designed to handle the home’s critical loads. You can pre-wire individual items on each circuit, such as the refrigerator, WiFi and living room outlets, LED lighting, ceiling fans, garage doors, a home office, security systems, medical devices, and gas appliance ignition (hot water and stove).
Does the rough-in require specialized components or retraining for my electricians?
The Bronco All-In-One is designed to offer a familiar installation approach for electrical contractors. The enclosure mounts easily between standard framing with studs spaced 20 inches inside to inside. It utilizes standard, trusted components, assembling Siemens load centers (such as PN4040L1200C and E0816ML1125i) to the mounting plates.
Is the integrated system fully certified and covered by a warranty?
Yes. The Bronco All-In-One is a fully UL Listed integrated system. It is engineered for fully automatic operation with zero scheduled maintenance required, and it comes backed by a 5-year manufacturer warranty.
Build Smarter. Build Backup Ready.
Whether you are developing a single-family home or a multi-unit condominium, the Bronco All-In-One is your clear choice for integrated power protection. Reach out to our team to get started.